Strategies for compatibilization of polymer/waste tire rubber systems prepared via melt-blending
October 2024
Waste tires are a low-cost and high-calorific alternative fuel, therefore energy recovery is still very popular method of their utilization. On the other hand, waste tires are composed from high quality...
Share article
Compatibility issues in high voltage DC cable insulation development
October 2024
In the last decade, growing efforts were made to replace crosslinked XLPE insulations with thermoplastic ones in high-voltage DC cables. The main reason for these development projects is the injection...
Share article
Polymer compatibility and interfaces in extrusion-based multicomponent additive manufacturing – A mini-review
October 2024
One of the most widespread versions of additive manufacturing technologies (AM) is fused filament fabrication (FFF) or fused deposition modeling (FDM), using polymer melts to print freeform structures....
Share article
Intramolecular cooperation and biphasic flame retardant mode of action: Effectiveness of hexa(1,2,4-triazol-3-ylamine) cyclotriphosphazene in epoxy resin
July 2024
The substitutional structure of cyclotriphosphazene derivatives significantly influences their flame-retardant effectiveness. A cyclotriphosphazene derivative with triazole group, referred to as hexa(1,2,4-triazol-3-ylamine)...
Share article
Surface grafting POSS to improve the hydrophobicity and fire safety of polyrotaxane based smart phase change materials
July 2024
Polyethylene Glycol (PEG)-based flexible phase change materials have broad and practical application value in thermal management of flexible electronic devices. Considering the typical application cases...
Share article
Fire performance durability of flame retardants in polymers and coatings
July 2024
The fire performance durability of products containing flame retardants may be significantly affected after aging and mechanical recycling. Publications of the last ten years show that even under severe...
Share article
Review of thermal conductivity in epoxy thermosets and composites: Mechanisms, parameters, and filler influences
July 2024
Rapid development of energy, electrical and electronic technologies has put forward higher requirements for the thermal conductivities of epoxy resins and their composites. However, the thermal conductivity...
Share article
Advances in flame retardancy of asphalt pavement: A review
July 2024
Asphalt pavement is widely applied to the surface in high-grade highway tunnels due to its prominent preponderance in road performance. However, asphalt is flammable as the binder material to adhere...
Share article
Improving the flame retardancy properties of PLA/PC blends
July 2024
Polylactic acid/Polycarbonate (PLA/PC) blend was prepared via twin screw extruder by taking the bio-based content as much as possible and the better mechanical, thermal, and impact properties into consideration....
Share article
Simple modification of phenylphosphonic acid to construct polyester-cotton fabrics with high flame retardancy
July 2024
Polyester-cotton fabrics (PTCO) have excellent properties and are ubiquitous in daily life, but their serious flammability brings great safety hazards to people's lives. This study used phenylphosphonic...
Share article
Novel four-in-one intumescent flame retardants for polypropylene: Synthesis, characterization and properties
July 2024
To address the shortcomings of traditional intumescent flame retardants (IFRs), a novel four-in-one IFR (M [APP/NiCo2O4]) was constructed for the first time. It integrates acid source, gas source, carbon...
Share article
Tunable honeycomb-hierarchical multiscale structures of 2D/3D porous PLA/CCN composite films fabricated by the breath figure method
April 2024
Highly ordered porous structures of PLA composite films can be designed with the addition of calcium carbonate nanoparticles (CCN) in polymeric film formation using the breath figure (BF) technique...
Share article
Bismuthene nanosheets prepared by an environmentally friendly method and their thermoelectric epoxy nanocomposites
April 2024
Theoretical research has predicted high thermoelectric performance for bismuthene nanosheets, but it is a great challenge to prepare these nanosheets due to low efficiency and intensive oxidation. We...
Share article
Bimodal impact strength distribution in HDPE composites: Formulational effects and Bayesian inference
April 2024
A bimodal impact strength distribution was found in notched impact specimens of HDPE composites with calcium carbonate, carbon black, SEBS and stabilisers. The bimodal distribution was only found at...
Share article
Novel manufacturing method for highly flexible poly(lactic acid) foams and ferroelectrets
April 2024
Poly (lactic acid) (PLA) foams have demonstrated a high variety of functional characteristics, still, the rigidity of this cellular material remains a major limiting factor when it comes to implementation...
Share article
Application of radical dendrimers as organic radical contrast agents for magnetic resonance imaging
April 2024
To develop metal-free magnetic resonance imaging (MRI) contrast agents, organic radical based contrast agents have been proposed as a promising alternative to obtain less toxic and safer MRI contrast...
Share article
Multifaceted applications of thymol/carvacrol-containing polymeric fibrous structures
April 2024
Nowadays there are many attempts for sustainable development due to rapid industrialization. In this context, thymol and carvacrol, which are obtained from many plants, are highly promising components...
Share article
Strategies to resolve intrinsic conflicts between strength and toughness in polyethylene composites
April 2024
The brittle fracture pattern in plastics associated with low toughness performance have a negative effect on their performance especially for long-term and specialized applications. This review provides...
Share article
Product, process, property, and performance (PPPP) relationship of 3D-Printed polymers and polymer composites: Numerical and experimental analysis
April 2024
Understanding the external and internal factors during an additive manufacturing (AM) process is crucial, as they can significantly affect the final product's performance. Efforts have been made to...
Share article
Mechanism of polymer composite-based nanomaterial for biomedical applications
January 2024
Recent developments in nanomaterials have come to extensive use in various fields, especially in the biomedical industry. Numerous significant obstacles still need to be overcome, particularly those...
Share article
Production and hosting by Elsevier on behalf of KeAi Communications Co. Ltd